EVISA ATEX HV range in E65.R, E100.R, E200.R and E300.R sizes. Compare model-specific 50 Hz data, performance curves and drawings. Ask Girovac to confirm the gas, dust or combined configuration for your installation.
Tell us the configuration and quantity you need. Include your process requirements if you would like help with selection.
View quote listThe EVISA ATEX range uses single-stage oil-lubricated rotary vane technology. The supplied catalogue covers E65.R, E100.R, E200.R and E300.R ATEX HV versions at 50 Hz. Choose the precise gas, dust or combined configuration as well as the required pumping performance.
Send Girovac the required area classification, process-gas or dust details, temperature requirements and duty point. The catalogue is a selection reference; suitability must be checked against the current documentation and marking for the exact pump and installation.
| Model | Nominal flow | PNEUROP speed | Speed at 1 mbar | Motor |
|---|---|---|---|---|
| E65.R ATEX HV | 68 m³/h | 65 m³/h | 40 m³/h | 1.5 kW |
| E100.R ATEX HV | 100 m³/h | 96 m³/h | 52 m³/h | 2.2 kW |
| E200.R ATEX HV | 200 m³/h | 190 m³/h | 134 m³/h | 4 kW |
| E300.R ATEX HV | 300 m³/h | 280 m³/h | 171 m³/h | 5.5 kW |
All four ATEX HV tables state end vacuum of ≤ 0.06 mbar at 50 Hz with gas ballast closed or without gas ballast. Opening gas ballast changes the stated end vacuum. The E65.R and E100.R use 1¼-inch BSP inlet and outlet connections; E200.R and E300.R use 2-inch BSP.
The catalogue describes an integrated exhaust oil-mist filter and temperature monitoring by an intrinsically safe PT100. Oil-level monitoring, filters, hoses and other accessories have separate references. Confirm the monitoring arrangement and scope of supply rather than assuming every listed accessory is included.
The E65.R, E100.R and E200.R tables list three-phase 230/400 V at 50 Hz. The E300.R table distinguishes 230/400 V for dust or gas versions and 400/690 V for the combined dust-and-gas version. Check the selected pump reference against the electrical supply.
Expand the relevant model below to see its original 50 Hz pump-down and pumping-speed curves and dimension drawing. The pump-down plots use a 1,000 litre vessel. Actual cycle time also depends on the system and process; these are not power-consumption graphs.
Oil capacity: 3 litres; specified standard lubricant: MV99S synthetic. Noise: 67 dB(A) at 50 Hz. Open this ATEX model’s manufacturer tables and references.
Oil capacity: 3 litres; specified standard lubricant: MV99S synthetic. Noise: 67 dB(A) at 50 Hz. Open this ATEX model’s manufacturer tables and references.
Oil capacity: 5 litres; specified standard lubricant: MV99S synthetic. Noise: 71 dB(A) at 50 Hz. Open this ATEX model’s manufacturer tables and references.
Oil capacity: 5 litres; specified standard lubricant: MV99S synthetic. Noise: 72 dB(A) at 50 Hz. Open this ATEX model’s manufacturer tables and references.
Provide the full model reference, serial number and marking when asking for service parts. Use the applicable manufacturer instructions and configuration-specific kit references. Standard EVISA parts or accessories should not be assumed interchangeable with an ATEX assembly.
Discuss servicing with Girovac
No. The ATEX range has its own configurations, monitoring and reference numbers. A shared model size or pumping-speed figure does not establish the same suitability.
No. The manufacturer catalogue distinguishes gas, dust and combined configurations. Give Girovac the required classification and process details so the exact documentation and configuration can be checked.
The ATEX tables and curves in the supplied document are at 50 Hz. Do not transfer another version’s frequency or performance data to an ATEX assembly.
Send the required classification, process composition, target pressure, gas load, electrical supply and installation details. For a replacement, include a clear nameplate photograph and serial number.
Download the MIL’S EVISA / EVISA ATEX manufacturer catalogue (PDF, 6.4 MB). The ATEX section starts at PDF page 57, printed page 58. Model tables, drawings and curves are on printed pages 60–67. Listing expanded September 2026 from the supplied manufacturer document.
| Manufacturer | MIL'S |
|---|---|
| Equipment type | Single Stage Rotary Pumps / Single Stage Oil Filled Pumps |
| Nominal pumping capacity | 68 / 100 / 200 / 300 m³/h at 50 Hz for E65 / E100 / E200 / E300 respectively |
| End / ultimate pressure | ≤ 0.06 mbar at 50 Hz; ATEX HV with gas ballast closed / without gas ballast |
| Lubricant | MV99S synthetic in the supplied ATEX tables; confirm application-specific requirements |
| Pumping technology | Single-stage oil-lubricated rotary vane; ATEX HV configurations |
| Models in this range | E65.R ATEX HV; E100.R ATEX HV; E200.R ATEX HV; E300.R ATEX HV |
| Configuration | Gas, dust or combined configuration: confirm the exact marking and model reference |
Send the pump model and part number when asking about a replacement. Compatibility depends on the equipment and operating conditions.
Confirm the exact version, electrical supply and connections. Ask whether oil, filters, fittings, cables or controllers are included or separately specified.
Availability, lead time and the applicable warranty are confirmed for your quotation. A catalogue listing does not reserve stock.
What to check in your quotation · Delivery · Returns and faults
MIL’S EVISA ATEX Rotary Vane Vacuum Pumps
Prefer to talk? 01692 660 117 · [email protected]
We use your details to respond to your enquiry. Read our privacy policy.
MIL'S
DVP
DVP
DVP
Compare the stated conditions as well as the values. A missing specification is not a zero rating; confirm suitability with Girovac.
Copyright © 2026 Girovac Ltd | Registered in England and Wales Number: 01758137 | Cookie Policy | Privacy Policy | Delivered by Postino
